Tutorial: FusionSilicon X1 12.5GH Lyra2rev2 Miner

2 Comments 355 Views0


Tutorial FusionSilicon X1 12.5GH Lyra2rev2 Miner IMG N01

This tutorial is intended for the FusionSilicon X1 which is a Lyra2rev2 miner manufactured by FusionSilicon. The FusionSilicon X1 is a mining machine that supports the Lyra2rev2 algorithm, all coins based on Lyra2rev2 algorithm supported, such as XVG, MONA, VTC. For Lyra2rev2 mining, its hashrate is as high as 12.5GH/s, whereas the power consumption is only 1040w.

We will take FusionSilicon X1 as an example to show settings and troubleshootings which apply equally to other FusionSilicon models.

 

Miner Specifics

BrandFusionSilicon X1
AlgorithmLyra2rev2 algorithm
Hash Rate12.50 GH/s ± 5%
Power Consumption1040w ± 10%
Supported CoinsXVG, MONA, VTC etc.
PSUNo PSU

 

Preparations

The following background knowledge would be helpful to use the miner:

You need to decide what currency you what to mine and what the pool you want to use. You need to choose one of the mining pools and create a mining worker account in that pool. Also, it is recommended that you have a look at the “Help” section of your mining pool.

In our tutorial, we will use the NiceHash for Lyra2rev2 mining.

NiceHash Mining Pool Screenshot

 

Miner Connection

  • Connect the miner to the LAN port on the same router which your computer is also connected to. The miner is stand-alone, your computer is just needed for miner configuration. And a PSU > 1200w with 6PIN x 10 needed for the miner.
  • This is how you will receive the miner from EastShore. Check if the cables on the miner are connected tightly (they could loosen up during shipping).

FusionSilicon X1 12.5GH Lyra2rev2 Miner IMG 06

  • There are three hashboards, each with three 6PIN ports on it, and a black 6PIN port on the controller for a total of 10 6PIN ports. All the TEN 6PIN ports will be used for mining.

FusionSilicon X1 12.5GH Lyra2rev2 Miner IMG 10

  • Get your PSU ready. There should be TEN 6PIN connectors on your PSU, all the TEN 6PIN ports on the miner should be connected to your PSU.

FusionSilicon X1 12.5GH Lyra2rev2 Miner IMG 13

  • Connect the ethernet cable and power cord, then, miner connection is DONE.

FusionSilicon X1 12.5GH Lyra2rev2 Miner IMG 02

 

Mining Guide

  • Make sure you connected the miner properly. Then, power on your PSU.
  • Wait for 1~3 minutes. (The miner needs about 1~3 minutes to initialize itself. Please wait patiently.)
  • Scan the IP address of your miner: The “Network Protocol” of the miner is “DHCP”. The IP address will be different under different networks. You can refer to this blog for scanning instructions: How to find out the IP address of your crypto miner
  • Log into the miner configuration page:   Run your Internet browser, such as Google Chrome. and open the IP address you just scanned (For example, 192.168.1.82). The password is “fusion“.

Tutorial FusionSilicon X1 12.5GH Lyra2rev2 Miner IMG 01

  • Sometimes, you may not be able to log into the configuration page immediately, please just wait for about 1 minute, then try to log again.
  • Then, the “Homepage” of the miner will display.

Tutorial FusionSilicon X1 12.5GH Lyra2rev2 Miner IMG 02

  • Click the “Miner Configuration” tab at the top of the page for mining account settings.

Tutorial FusionSilicon X1 12.5GH Lyra2rev2 Miner IMG 04

  • Before setting your mining account, you should first take a look at the “HELP” page of your mining pool to know the mining URL of your pool.
  • In our test, we used NiceHash  for Lyra2rev2 mining. According to its HELP page, we set our pool URL of the miner as:

Pool URL:  stratum+tcp://lyra2rev2.hk.nicehash.com:3360

Pool Worker: 32E……….XM (Your mining ADDRESS)

Pool Password: 123123

  • After setting your mining account details, save the settings by clicking “Save & Apply“.
  • Wait for 1~3 minutes, then the miner will reload the mining settings and start mining with the mining account you just set.
  • You can check the mining details on the “Miner Status” page. The mining speed showing here will be refreshed every 5 seconds.

FusionSilicon X1 12.5GH Lyra2rev2 Miner Speed Test

  • You can check the working details of three hashboards in the “Miner Status” -> “Modules” page.

Tutorial FusionSilicon X1 12.5GH Lyra2rev2 Miner IMG 03

  • If your miner works perfectly, you don’t need to change anything else(including other settings in “System”, “Network” tabs). If you don’t know what you are doing, don’t tweak it.
  • Now, you are all set up. Let the beautiful machine work and earn money for you.

 

Leave a Reply